Removal of vacuum aluminum brazing furnace oil need to pay attention to the problem

Removal of vacuum aluminum brazing furnace oil need to pay attention to the problem

1, to 400 degrees Celsius temperature quickly, in order to reduce the diffusion brazing junction silicon, is helpful to ensure the quality of joints. As this is aluminum brazing process requirements, must do it.
2, then take a slow long natural cooling, this step is to cleanse sandstones from fouling. At this time due to the furnace with nitrogen gas, waste heat by the cycle of nitrogen} L conduction, radiation to heat was less than the adsorption with the cold components of oil pollution. The temperature of these artifacts usually only tens of degrees, in the process can increase to 200 degrees Celsius, so as to achieve its evaporation table and pollution of the day.
3, the next coarse vacuum, one party but would have vaporized oil steam out of furnace chamber, prevent again by adsorption after cooling, the other party and, in the crude oil evaporation under vacuum environment will be more thorough. Diffusion pump no need to open, because when pressure drop to 10 pa, more than 99.99% in furnace gas has been pulled out.
4, closed cooling water of furnace wall, furnace door is to reduce heat loss, is more advantageous to raise the temperature of furnace wall. However, because the diffusion pump need cooling of equipment, can't stop water cycle system.
5, and other issues
Through such processing, baffle plate and oil base on some of the heat capacity of the smaller components can be cleared away. Wall due to the heat capacity, although closed cooling water in advance, but still kept cooling water increase the heat capacity of National People's Congress, the temperature is still rising gao, clean from the effect of oil pollution is the worst. So, in the final need to j ping work cleaning furnace wall. Because the oil is accumulated for a long time, the oil will stick with dust, is can't use this method to remove dust, oil pollution has been removed, the remaining dust adhesion is not strong, can use a vacuum cleaner to clean up, or use the clean compressed air to blow away. Can't clean the furnace wall and the last to do that, and heating evaporation, and there will be some oil vapor by adsorption. When removing dust will be, ash, _ stick. So the wall should be on the final wash clean.

Pump vacuum brazing furnace temperature is too high

Pump vacuum brazing furnace temperature is too high

Vacuum brazing furnace will inevitably be in the process of using all kinds of fault, pump vacuum brazing furnace temperature is too high? The following vacuum furnace manufacturers to share the solution.
(1) check the thermostat setting of the temperature control pump is in accordance with the regulations. If not, should be reset.
(2) pump cooling water flow rate of solid scale or other dirt jam for smaller. Lead to rising pump Yun. Because oil pump must have certain viscosity to ensure the sealing of pump. The viscosity is too small, the sealing performance variation. And pump oil viscosity with temperature rise and fall. The sealing of pump, oil saturation vapor pressure increases, vacuum degree reduced. Solution is to dredge waterways. Increase the flow of cooling water, the temperature of the oil pump shall not exceed 0 ℃ o l e., it is about 0 ℃.
(3) components assembly is undeserved, cause wear and tear, should be reassembled.

Vacuum brazing furnace and practical environmental protection

Vacuum brazing furnace and practical environmental protection

1 9 7 for 5 years, have 2 00. More than one generation now used in the vacuum brazing furnace put into production. Vacuum brazing furnace, used for soldering estimates about 10%. A lot of the early products meet the strict requirements of aerospace products, in recent years the trend has been towards general industrial situations. As long as carefully review the benefits of this modern tool, this choice is to is self-evident. Vacuum brazing furnace can produce cleaner, precision machining, metallurgy quality products, there are some did not use a vacuum brazing cannot be made into the final shape. Due to cancel the cleaning after soldering, and lower cost. This method can also be used to produce component combination of many small, low-cost products, instead of using large pieces of material machining or welding pieces together. Vacuum brazing furnace, of course, little harm the environment.

Maintenance of vacuum brazing furnace

Maintenance of vacuum brazing furnace

Continuously operating on a daily basis - with no filler metal with vacuum brazing furnace to various parts of the vacuum brazing furnace, inevitably lead to some vacuum brazing furnace charge fly all the damage to the heating elements and heat shield. If not timely maintenance, vacuum brazing furnace metal deposition, will soon be corrosion damage to the heating element, or produce local overheating, or make the heating system is broken one or more of the phase. That leads to the temperature of the inhomogeneity, in batch vacuum brazing furnace production, this kind of situation is often not noticed. Heating element of repair is the easy, it is not the same as heat insulation screen damage.
If heat insulation screen USES the key persons, as long as the screen with a thin layer of ink stone protection can make the vacuum brazing furnace metal splash damage down to the most. Vacuum brazing furnace metal and graphite surface wetting and bonding, not simply in the form of beads drops roll to the cold of the furnace area. After completion of these particles in a vacuum brazing furnace, also not harm can easily be removed.